Arduino 9 Axis 9 DOF Accelerometer, Gyroscope and Compass Module

SKU: TA0253


$16.95
RRP $34.95
In Stock

Buy In Bulk & Save!
Buy 4 to 10: Pay $16.10 ea
Buy 11 to 20: Pay $15.29 ea
Buy 21 to 100: Pay $14.53 ea


Calculate Shipping

Gyroscope Features:

The triple-axis MEMS gyroscope in the MPU-9250 includes a wide range of features:
• Digital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-programmable fullscale range of ±250, ±500, ±1000, and ±2000°/sec and integrated 16-bit ADCs
• Digitally-programmable low-pass filter
• Gyroscope operating current: 3.2mA
• Sleep mode current: 8µA
• Factory calibrated sensitivity scale factor
• Self-test

Accelerometer Features:

The triple-axis MEMS accelerometer in MPU-9250 includes a wide range of features:
• Digital-output triple-axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g and integrated 16-bit ADCs
• Accelerometer normal operating current: 450µA
• Low power accelerometer mode current: 8.4µA at 0.98Hz, 19.8µA at 31.25Hz
• Sleep mode current: 8µA
• User-programmable interrupts
• Wake-on-motion interrupt for low power operation of applications processor
• Self-test 2.3 Magnetometer Features The triple-axis MEMS magnetometer in MPU-9250 includes a wide range of features:
• 3-axis silicon monolithic Hall-effect magnetic sensor with magnetic concentrator
• Wide dynamic measurement range and high resolution with lower current consumption.
• Output data resolution of 14 bit (0.6µT/LSB) or 16 bit (15µT/LSB)
• Full scale measurement range is ±4800µT
• Magnetometer normal operating current: 280µA at 8Hz repetition rate
• Self-test function with internal magnetic source to confirm magnetic sensor operation on end products

Additional Features:
The MPU-9250 includes the following additional features:
• Auxiliary master I2C bus for reading data from external sensors (e.g. pressure sensor)
• 3.5mA operating current when all 9 motion sensing axes and the DMP are enabled
• VDD supply voltage range of 2.4 – 3.6V
• VDDIO reference voltage for auxiliary I2C devices
• Smallest and thinnest QFN package for portable devices: 3x3x1mm
• Minimal cross-axis sensitivity between the accelerometer, gyroscope and magnetometer axes
• 512 byte FIFO buffer enables the applications processor to read the data in bursts
• Digital-output temperature sensor
• User-programmable digital filters for gyroscope, accelerometer, and temp sensor
• 10,000 g shock tolerant
• 400kHz Fast Mode I2C for communicating with all registers
• 1MHz SPI serial interface for communicating with all registers

Module Pinout:
•    VCC......3.6 to 6V supply (on-board 3.3V regulator)
•    GND......0V
•    SCL......I2C serial clock
•    SDA......I2C serial data
•    EDA......Auxiliary I2C master serial data
•    ECL......Auxiliary I2C Master serial clock
•    AD0......I2C Slave Address LSB (AD0)
•    INT......Interrupt digital output (totem pole or open-drain)
•    NCS.....Chip select (SPI mode only)
•    FSYNC..Frame synchronization digital input. Connect to GND if unused.

SKU TA0253
Barcode # 2000000004082
Brand iDuino
Shipping Weight 0.1000kg
Shipping Width 0.100m
Shipping Height 0.030m
Shipping Length 0.180m
Shipping Cubic 0.000540m3
Unit Of Measure ea

Be The First To Review This Product!

Help other Aus Electronics Direct users shop smarter by writing reviews for products you have purchased.

Write a product review

We Also Recommend

You May Also Like

Others Also Bought

More From This Category